Model:FSP-w/c
Our Optical Splice Closure are all made in China. Jecsany is one of professional the Optical Splice Closure manufacturers and suppliers in China.Optical splice closures are used to distribute, splice, and store the outdoor optical cables which enter and exit from the ends of the closure. There are two connection ways: direct connection and splitting connection. They are applicable to situations such as overhead, man-well of pipeline, embedded situation etc. Comparing with terminal box, the closure requires much stricter requirement of seal. Sealing ring and air valve are required for closure, but that are not necessary for terminal box.
Model:SC(B)30-6
The dry-type transformer consists of an iron core composed of silicon steel sheets and a coil cast with epoxy resin. An insulating cylinder is placed between the high and low coils to increase electrical insulation, and the coils are supported and restrained by a pad.
Because epoxy resin is flame retardant, flame retardant, self-extinguishing solid insulating material, that is, safe and clean. With oil-free, inflammable, low operating loss, outstanding disaster prevention ability, it is widely used in high-rise buildings, airports, wharfs, power plants, residential areas or complete substations and other places.
Model:HRH-B/33F-630-25kA
Pole-mounted Disconnector Switch 33KV is an electrical device for the reliable disconnection of certain sections of a high-voltage electrical network when there is no current in them. The use of isolating switches (either alone or in combination with high-speed short-circuiting devices) makes it possible to simplify the arrangement of switching points and transformer substations and to eliminate expensive high-voltage circuit breakers.
In the case of damage to certain sections of a network, the circuit breakers operate first, and then the isolating switches automatically disconnect the damaged section, after which the circuit breakers close again and restore electric power to the rest of the consumers on the network. Isolating switch......
Model:GW9-15/600
An electrical device for the reliable disconnection of certain sections of a high-voltage electrical network when there is no current in them. The use of isolating switches (either alone or in combination with high-speed short-circuiting devices) makes it possible to simplify the arrangement of switching points and transformer substations and to eliminate expensive high-voltage circuit breakers.
Model:GW9-27/600
An electrical device for the reliable disconnection of certain sections of a high-voltage electrical network when there is no current in them. The use of isolating switches (either alone or in combination with high-speed short-circuiting devices) makes it possible to simplify the arrangement of switching points and transformer substations and to eliminate expensive high-voltage circuit breakers.
Model:FLN36-12
indoor high voltage AC load breaker switch refer to international new technology and develop the switching equipment in according to the relevant standards in China's electric power system.
Model:Hydraulic Cable Lug Terminal Crimping Tool
This item is a hydraulic crimper tool kit which is used for crimping and joining aluminum, copper wires, cables. for marine and architectural wire rope swage assembly applications. Great for swaging and crimping with maximum holding power. The tool is safe and doesn't tear the wires or cables/hoses during crimping
Model:35kv Heat Shrink Termination Kit outdoor Cable Accessories
Heat Shrink outdoor Termination Kit shrinkable cable termination kit raychem is widely used in the indoor and outdoor directly and intermediate terminal connection of every kinds of power cable. These Heat Shrinkable Termination Kits are easy to install and designed in compliance with the international design standards.
Model:WSY-15 Heat Shrink Termination Kit 15kV outdoor cable accessories
Indoor / Outdoor shrinkable cable termination kit raychem is widely used in the indoor and outdoor directly and intermediate terminal connection of every kinds of power cable. These Heat Shrinkable Termination Kits are easy to install and designed in compliance with the international design standards.
Model:M12
The M12 stainless steel bolt and hex nuts is used with bolts and screws to connect and tighten the parts.
Model:CPT AU
Pre-Insulated Terminal Crimping Ring Bimetal Cable Lugs are applicable for LV-ABC lines with insulated conductors, suitable for insulated aluminum conductors in installation of service line system, streetlightning, buildings.
Model:ES 800
Plastic ADSS Suspension Clamp ES-800, other called ADSS supporting clamp is developed to clamp and support round ADSS cable during outdoor FTTX network constructions.ES 800 plastic adss Suspension Clamp Assembly is dielectric and can be applied in straight direction or in line deviation angle up to 90.